Survival bracelet 15 in 1. Survival bracelet

Jacket: - loose fit; - central side fastener, wind flap, buttons; - yoke made of finishing fabric; -2 welt slanted pockets with a flap, with buttons at the bottom of the front; - 1 patch slanted pocket on the sleeves; - reinforcing shaped pads in the elbow area; - bottom of sleeves with elastic; - double hood, with a visor, has a drawstring for volume adjustment; - adjustment at the waist using drawstrings; Trousers: - loose fit; -2 side vertical pockets; - in the knee area, on the back halves of the trousers along the seat seam - reinforcing linings; -2 side patch pockets with flap; -2 rear patch pockets with buttons; - the cut of the parts in the knee area prevents them from stretching; - the back halves under the knee are assembled with an elastic band; - elastic waistband; - bottom with elastic; - fastened braces (suspenders); - belt loops; wearing - both in boots and outside. material: tent fabric; composition: 100% cotton; density: 270 gr.; Overlays: ripstop, oxford; cuffs: yes; rubber seals: yes; jacket/pants pockets: yes/yes; additionally: lightweight summer version; high strength of fabric and seams; How to wash a Gorka suit.

A summer suit consists of a jacket and trousers. It is part of the all-season basic uniform kit (VKBO). A suit made of Mirage fabric (PE-65%, cotton-35%), with a high cotton content, is hygienic and comfortable for daily wear. Straight-cut jacket. The collar is a stand-up collar, the volume is regulated by a patch on a textile fastener. The central fastener has a detachable zipper closed with a flap with textile fasteners. Two chest patch pockets with flaps and textile fasteners. Back with two vertical folds for freedom of movement in the shoulder blade area. Single-seam sleeves. At the top of the sleeves there are patch volume pockets with flaps with textile fasteners. In the elbow area there are reinforcement pads with an entrance for protectors with textile fasteners. At the bottom of the sleeve there is a patch pocket for pens. At the bottom of the sleeves there are cuffs with textile fasteners to adjust the volume. Straight cut trousers. The belt is solid with seven belt loops. The volume of the belt is adjusted with a cord with tips. Button closure. Two side welt pockets. Along the side seams there are two large patch pockets with three folds for volume. The upper part of the pockets is tightened with an elastic cord with a lock. The entrances to the pockets, designed obliquely to resemble the hand, are closed with flaps with textile fasteners. In the knee area there are reinforcement pads with an input for protectors with textile fasteners. At the bottom of the trousers there are patch pockets with flaps with textile fasteners. The volume at the bottom of the trousers is adjustable with tape. The back halves of the trousers have two welt pockets with flaps and a hidden button closure. Reinforcement pad in the seat area

Semi-fitting dress in dark blue with a V-neck, decorated with a red silk scarf (included in the set). Fabric - gabardine. According to the order of the Ministry of Internal Affairs of Russia No. 575, chevrons are sewn onto the sleeves of the dress at a distance of 8 cm from the edge of the shoulder. A chevron is sewn onto the left sleeve indicating membership in the Ministry of Internal Affairs of Russia, and on the right sleeve there is a chevron designating the service of a police/justice officer. You can add Velcro to the chevrons. The scarf is worn with the dress in a triangle folded into a scarf, the narrow ends are tied together and tucked into the back under the collar. The wide side is tucked inside under the neckline of the dress. It is allowed to wear a summer dress without a scarf in office premises. The length of the dress along the bottom edge should be at knee level. The Police/Justice dress with short sleeves is part of the new police uniform. Example of material pattern:

The Gorka-3 suit is the most successful and widespread type of Gorka suit. Made from 270g rip-stop material. per 1 m2, black, structurally consists of a jacket and trousers. Used to protect the fighter from adverse weather conditions, all-season. The main difference of this suit is the fleece lining. The jacket has a deep hood with drawstrings, two side welt pockets covered with flaps fastened with a button, one internal pocket for documents and two pockets on the sleeves, just below the shoulders. It is worth noting that the fleece lining is removable, which increases the usability of the suit and allows it to be used in a wider temperature range. The shoulders, elbows, and cuffs are reinforced with synthetic rip-stop Oxford fabric 0. The reinforcement on the elbows of the mountain suit-3 is made in the form of a Velcro pocket and is equipped with rigid inserts. The sleeves are equipped with anti-dust cuffs and a hidden elastic band for volume adjustment just above the wrist. The jacket is also equipped with an adjustable drawstring along the edge and fastens with buttons. The trousers of the slide suit have six pockets. Two side slots, two cargo slips and two rear ones. The knees, the bottom of the legs and other loaded areas of the trousers are reinforced with synthetic rip-stop Oxford fabric 0. The bottom of the legs is double, the so-called “boot”, reinforced with a cuff that fits over the boot and prevents dust, dirt and small stones from getting into it. Just below the knee, the trousers have a fastening elastic band. It automatically adjusts the volume of the trouser leg and prevents the fabric from sailing. The trousers are equipped with removable suspenders. Main features: removable fleece lining demi-season suit strong material internal pocket hood CHARACTERISTICS SUIT CHARACTERISTICS Material: ripstop Composition: 70/30 Density: 240 g. Linings: Oxford 0 Cuffs: yes Sealing elastic bands: yes Jacket/pants pockets: yes/yes Seasonality: demi-season Additional: reinforced inserts, removable fleece lining, dust boots on trousers, suspenders included

Material: 100% Cotton Product weight: 52 size -232 g 54 size -265 g

Fabric: Mirage-210, pe-67%, xl-33% The summer suit consists of a jacket and trousers. Straight-cut jacket. Stand collar. The central fastener has a detachable zipper closed with a flap with textile fasteners. Two chest patch pockets with flaps and textile fasteners. The pockets are located obliquely, along the direction of the hand. Back with two vertical folds for freedom of movement in the shoulder blade area. Single-seam sleeves. In the upper part of the sleeves there are patch volume pockets with flaps with textile fasteners, with belt loops on the inside of the flaps. In the elbow area there are reinforcement pads with an entrance for protectors with textile fasteners. At the bottom of the sleeves there are patch pockets for pens. At the bottom of the sleeves there are cuffs with textile fasteners to adjust the volume. Straight cut trousers. The belt is solid with seven belt loops. The volume of the belt is adjusted with a cord with tips. Button closure. Two side welt pockets. Along the side seams there are two large patch pockets with three folds for volume. The upper part of the pockets is tightened with an elastic cord with a lock. The entrances to the pockets, designed obliquely to resemble the hand, are closed with flaps with textile fasteners. In the knee area there are reinforcement pads with an input for protectors with textile fasteners. At the bottom of the trousers there are patch pockets with flaps with textile fasteners. The volume at the bottom of the trousers is adjustable with tape. On the back halves of the trousers there are two welt pockets with flaps and a hidden fastener.

Please note - this model has fleece insulation only in the jacket! Color: khaki Jacket: - loose fit; - central side fastener, wind flap, buttons; - yoke made of finishing fabric; -2 welt slanted pockets with a flap, with buttons at the bottom of the front; - 1 patch slanted pocket on the sleeves; - reinforcing shaped pads in the elbow area; - bottom of sleeves with elastic; - double hood, with a visor, has a drawstring for volume adjustment; - adjustment at the waist using drawstrings; Trousers: - loose fit; -2 side vertical pockets; - in the knee area, on the back halves of the trousers along the seat seam - reinforcing linings; -2 side patch pockets with flap; -2 rear patch pockets with buttons; - the cut of the parts in the knee area prevents them from stretching; - the back halves under the knee are assembled with an elastic band; - elastic waistband; - bottom with elastic; - fastened braces (suspenders); - belt loops; wearing - both in boots and outside. material: tent fabric; composition: 100% cotton; density: 270 gr.; Overlays: ripstop, oxford 0; cuffs: yes; rubber seals: yes; seasonality: demi-season; additionally: reinforced inserts, removable fleece lining, dust covers on trousers, suspenders included

Scout suit moss The scout suit is made in a very successful design of the demi-season "Smok" uniform in the colors of the experimental A-TACS FG camouflage. The suit consists of a jacket and trousers. The jacket is long, below the waist. It is equipped with a deep hood with adjustable drawstrings, has four voluminous cargo pockets, closed with flaps on a large English button, which makes it easy to open the pocket in a hurry, with hands in shooting gloves, and in other extreme conditions, when the count of time has gone to seconds. The elbows of the suit are reinforced with an additional layer of fabric, the sleeves are equipped with wide rubber bands. The front zipper is duplicated along the entire length with smaller English buttons, which are fastened into a secret one. The trousers of the suit are loose-fitting, all loaded parts are reinforced with an additional layer of fabric. The belt has a wide rubber-fabric tape sewn into it, a thin cord for additional tightening, and loops for attaching suspenders. The trousers have four pockets. Two slotted ones, covered with flaps on a large English button, two overhead cargo ones, in which additional ammunition can be carried. At the bottom of the legs there is a wide cuff and so-called “brakes” made of elastic fabric that prevent the legs from riding up. color moss (A-TACS FG) Main features: color drawstring at the waist elastic bands on the pants carrying case suspenders included CHARACTERISTICS CHARACTERISTICS OF THE SUIT Material: T/S Composition: 65 PE /35 viscose Density: 160 g. Cuffs: yes Sealing elastic bands: no Jacket/pants pockets: yes/yes Seasonality: all-season Additional: carrying case

Consists of a jacket and trousers. Fabric - Rip-Stop, pe-67%, cotton-33%. Designed for employees of internal affairs bodies with special police ranks performing external service. Worn with a dark blue T-shirt and a dark blue cap. According to Order No. 575 of the Russian Ministry of Internal Affairs, chevrons are sewn onto the sleeves of a suit at a distance of 8 cm from the edge of the shoulder. A chevron is sewn onto the left sleeve indicating membership in the Ministry of Internal Affairs of Russia, and on the right sleeve a chevron indicating the service of a police officer is sewn. You can add Velcro to the chevrons. Above the left pocket (shelf), at a distance of 10 mm, is sewn a “POLICE” patch (110x30 mm), made in the shape of a rectangle with a red edging, the inscription is made in white or silver. A “POLICE” patch (275x85 mm), made in the shape of a rectangle with a red edging and a white or silver inscription, is sewn onto the back, 10 mm above the red line on the back. Employees with special police ranks wear badges on their summer suit jackets when serving in public places. The badges are attached with a pin to the left breast pocket. The badge is placed in a removable badge pocket, which is worn on the right side of the chest of dark blue summer suit jackets. The badge is a rectangular card containing the identification data of a police officer.

The jacket is part of the daily and weekend uniform of police officers of the new model. Worn with trousers. Material: Suit (wool blend) fabric. Composition: 75% wool, 25% polyester 280 g/m2 Lining: Twill 100% viscose 105% g/m2. Slim fit, single breasted, fastened with four buttons. Turn-down collar with lapels. Shelves with cut-off barrels. Horizontal welt side pockets in a “frame” with flaps. The back has a central seam, in the lower part of which there is a vent. Sleeves are set-in, two-seam. Jacket with lining. On the left shelf of the lining there is an internal pocket with a “leaf”. Designed for employees of internal affairs bodies with special police ranks, as well as for cadets (students) of educational institutions of higher professional education of the Ministry of Internal Affairs of Russia. Has red trim on the sleeves. According to Order No. 575 of the Russian Ministry of Internal Affairs, chevrons are sewn onto the sleeves of a suit at a distance of 8 cm from the edge of the shoulder. A chevron is sewn onto the left sleeve indicating membership in the Ministry of Internal Affairs of Russia, and on the right sleeve a chevron indicating the service of a police officer is sewn. You can add Velcro to the chevrons. In addition, shoulder straps with buttons are sewn onto this jacket, and two lapel emblems are also attached. How to sew on shoulder straps? For this, in addition to the jacket itself and shoulder straps, you will need a ruler, scissors, a needle, a thimble and strong red thread. Be sure to wear a thimble, even if you are used to sewing without one, as sometimes the needle passes through the shoulder straps with great difficulty, and you can injure your fingers. If you find it difficult to pull the needle and thread out of the shoulder strap, you can use pliers or tweezers. 1) First of all, prepare the shoulder straps, i.e. attach all the required insignia to it, since it will be much more difficult to do this on an already sewn shoulder strap. 2) Take the shoulder strap and position it so that the side farthest from the button is close to the seam that connects the shoulder of the jacket to the sleeve. At the same time, the upper edge of the shoulder strap, directed towards the back, should overlap the seam running along the shoulder by 1 cm. In other words, the shoulder strap should be slightly moved forward. 3) Thread a needle and fasten the shoulder strap to the jacket at three points: at the corners of the shoulder strap, at the place where it comes into contact with the sleeve seam and in the center of the semicircular cut. Now the shoulder strap will be securely fastened and will not move from the correct position during the sewing process. 4) Then very carefully sew the shoulder strap around the perimeter, making stitches in such a way that only barely visible points remain on its surface in those places where the needle enters the shoulder strap, and the thread between two adjacent holes passes mainly from the wrong side (along the lining) of the jacket . Then the thread will not be noticeable even if its color does not exactly match the color of the shoulder straps. In this case, the optimal length of each stitch should be about 1 cm. 5) With the second shoulder strap, follow the same pattern. How to strengthen lapel emblems? On the collar of the jacket - along the bisector (a line dividing the corner of the collar in half), at a distance of 25 mm from the corner of the collar to the center of the emblem, the vertical axis of symmetry of the emblem should be parallel to the flight of the collar. How to place awards on a police jacket? On the left side of the chest, awards are located in the following order: Insignia of special distinction are located so that the upper edge of the medal block is at the level of the ledge of the lapel of the tunic and jacket. When wearing two or more special insignia, they are arranged separately in one row, from right to left, with intervals of 10 mm between the lateral ends of the stars in the order listed. Special insignia of one designation are arranged in the order in which they were awarded. Badges of orders, orders and medals are arranged horizontally in a row from the center of the chest to the edge, from top to bottom in the order listed. When wearing two or more orders or medals, their blocks are connected in a row on a common bar. Orders and medals that do not fit in one row are transferred to the second and subsequent rows, located below the first, also placing them from the center of the chest to the edge in the above order. The blocks of orders and medals of the second row must go under the orders and medals of the first row, while the upper edge of the blocks of the bottom row is placed 35 mm below the blocks of the first row. Subsequent rows are arranged in a similar order. Badges of orders, orders and medals are located on the single-breasted police jacket so that the upper edge of the block of orders and medals of the first row is located 90 mm below the level of the lapel ledge. On the right side of the chest, awards are located in the following order: Orders are located from left to right in the order listed. The upper edge of the largest order of the first row is located at the level established for the common bar (block) of the first row of orders and medals placed on the left side of the chest. Orders that do not fit in one row are transferred to the second and subsequent rows located below the first, placing them also from the center of the chest to the edge in the indicated order. The centers of the orders in a row should be at the same level. The distance between orders and rows of orders is 10 mm. The sign of the number of wounds made of golden galun (for a severe wound) or dark red color (for a light wound) is located on the fabric strip of the top of the product. Braid width 6 mm, length 43 mm. The severe wound badge is placed below the light wound badge. The distance between stripes is 3 mm. The sign of the number of wounds is placed on the tunic and jacket to the right of the sign for honorary titles of the Russian Federation, and in its absence, in its place.

The Gorka WINTER suit produced by the PRIVAL trademark is made of dense cotton tent fabric with insulation: lining microfleece and fiberplast (warm siliconized polyester fabric). Cotton-blend raincoat fabric is used as finishing and reinforcement for areas critical to wear and getting wet. The jacket and trousers are loose-fitting, allowing you to add additional layers of clothing. For better fit, fit and to avoid “windage” in the wind, the suit has a system of ties based on rubber-fabric tape on the sides of the jacket, on the sleeves, under the knees and at the bottom of the trousers. The jacket has 5 pockets, the trousers 6. The pocket flaps are triangular in shape, which significantly reduces bending of the extreme corners of the flap and clinging to ammunition and equipment. The trousers are equipped with comfortable suspenders. The combination of overlays with the main khaki fabric ensures that the silhouette of a person is broken up at distant distances. The suit is designed to protect against temperature changes and strong winds in mountainous areas. Can be used by outdoor enthusiasts, fishing, hunting. Composition: jacket / trousers (equipped with special suspenders) Color: khaki, khaki inserts Fabric: tent 100% cotton, inserts - cotton-blend fabric Lining: microfleece Insulation: fiber plastic (siliconized fabric)

Gender: male Season: summer Camouflage color: khaki Material: “Tent canvas” (100% cotton), sq. 235 g/m2, VO Lining material: Mixed, sq. 210 g/m2, Regulatory technical documentation: GOST 25295-2003 Men's and women's coat outerwear: suits, jackets, vests, in Color: khaki Low temperature: 10 Fastener: buttons Country: Russia Description Jacket: loose fit; central fastener with loop and button; yoke, linings and pockets made of finishing fabric; 2 lower welt pockets with flap, loop and button; internal zip pocket with button; on the sleeves there is 1 patch slanted pocket with a flap for a loop and a button in the elbow area with reinforcing shaped overlays; bottom of sleeves with elastic; double hood, with a visor, has a drawstring for volume adjustment; waist adjustment with drawstring; Pants: loose fit; codpiece with loop and button fastening; 2 upper pockets in the side seams, in the knee area, on the back halves of the trousers in the seat area - reinforcing linings; 2 side patch pockets with flap; 2 rear patch pockets with buttons; the cut of the parts in the knee area prevents them from stretching; Dust-proof calico skirt at the bottom of the trousers; the back halves under the knee are gathered with an elastic band; elastic waistband; elastic bottom;

Thanks to innovative technologies and high-quality materials that provide maximum protection from rain and wind, you will be in constant comfort, which helps reduce fatigue throughout the day. Characteristics Protection from rain and wind Regular cut Upper material: Rip-stop Insulation: Thinsulate

The women's demi-season raincoat is part of the new uniform for police officers. The raincoat has a semi-fitting silhouette, with a central inner hidden fastener with five loops and buttons and an additional top button and a through-stitched loop, on an insulated stitched lining. On the yokes in the area of the shoulder seams there are two belt loops and one non-slit loop for attaching removable shoulder straps. Sleeves are set-in, two-seam. Patches are sewn into the lower part of the middle seam of the sleeve, fastened with a loop and a uniform button. Turn-down collar, with a detachable stand. The removable belt is threaded into belt loops located in the side seams and fastened with a buckle with a tongue, the free end of which is threaded into the belt loop. On the right hem there is an internal welt pocket with a leaf. Jacket fabric (100% polyester) with rip-stop weaving threads and water-repellent impregnation. The second layer is the membrane. Filler: Thinsulate 100 g/m. Recommended temperature range: from +10°C to -12°C. Worn with a dark blue muffler or a white muffler. It is allowed to wear a demi-season raincoat neatly folded with the front side out on the left hand. Demi-season raincoats are worn buttoned up. It is allowed to wear demi-season raincoats with the top button undone. Demi-season raincoats are worn with or without removable insulation and a belt fastened with a buckle. This raincoat has removable dark blue shoulder straps and dark blue stripes.

Jacket in “Retro” style With buttons Hood, adjustable to fit the shape of the face Elastic at the waist and at the bottom of the sleeves The bottom of the jacket is adjustable in size using a cord 4 external pockets Material: 100% cotton YOU MAY BE INTERESTED in: “And often in the evenings, evenings when I I’m suffocating from the comfort, suddenly there’s a whiff of crackling fires from the blue edge of the gas above the burner...” (B. Vakhnyuk) Once running home, we buried our faces in a rain jacket hanging on a hanger and inhaled the smell of a fire. Wearing rain jackets went on any hikes and at any time of the year. They were not bitten by mosquitoes, were not blown through, and did not melt from fire sparks. True, they froze, dried out slowly and were a bit heavy. Now that many lightweight modern jackets have appeared, real canvas windbreakers can be found quite rarely. But even now there is nothing better to find for a forest and a fire. Synthetics do not like fire. And if you don’t want your favorite fleece jacket to have a small (or large) hole, it’s time to remember the tarpaulin. The retro style jacket is made of high quality canvas. It is very durable and breathes well. And in general it is pleasant and loved, like Vizbor’s songs on a reel-to-reel tape recorder. The hood, adjustable to the contour of the face, elastic bands on the sleeves and drawstring at the bottom of the jacket protect against mosquitoes and wind. Matches, a compass, a map and other necessary items will easily fit in four spacious pockets. If you like to watch sunrises on a steep bank, wander through the summer tundra, pick cloudberries and cranberries in swamps, and sing in the evenings by the fire - this windbreaker is for you.

The Gorka suit produced by the PRIVAL trademark is made of cotton-blend fabric. The traditional Gorka suit is made from tent cotton fabric, and in areas where increased reinforcement is required, a cotton-blend fabric is placed, which is characterized by increased strength and wear resistance. This model is made entirely from cotton-blend fabric, so it will last a long time even with heavy use. Also, this material is pleasant to wear and will provide freedom and comfort in movement. The jacket and trousers are loose-fitting, allowing you to add additional layers of clothing. For better fit, fit and to avoid “windage” in the wind, the suit has a system of ties based on rubber-fabric tape on the sides of the jacket, on the sleeves, under the knees and at the bottom of the trousers. The jacket has 5 pockets, the trousers 6. The pocket flaps are triangular in shape, which significantly reduces bending of the extreme corners of the flap and clinging to ammunition and equipment. The trousers are equipped with comfortable suspenders. The combination of overlays with the main black fabric ensures that the silhouette of a person is broken up at distant distances.

The "Mountain-3" jacket is recommended for outdoor activities (hiking, hiking), as well as as a field uniform for mountain rifle units of the Russian Defense Ministry. Loose fit that does not restrict movement. Hood with adjustment in three dimensions - along the oval of the face, vertically at the back of the head and side adjustment vision With buttons Adjustment of the volume of the sleeve above the wrist with a hidden elastic band with Velcro Elbows are protected with a removable polyurethane foam insert (included) Pockets: two lower volume pockets with buttons, closed with flaps, a Napoleon pocket on the chest, inclined pockets on the sleeves, closed with flaps with Velcro, internal waterproof pocket for documents with Velcro Tightening: at the waist with a cord at the bottom of the jacket jacket View all products by tag jackets with a rubber cord Material: 100% cotton, new high-quality tarpaulin, superior to analogues used by most other manufacturers New processing technology has significantly improved the resistance of the fabric to fading and abrasion Reinforcing linings -100% polyester polyester View all products by tag polyester rip-stop Attention! Before washing, remove the protective inserts in the knee/elbow pads from the corresponding pockets. Do not wash protective inserts in a washing machine. When washing tarpaulin items in a washing machine, traces of wear may appear. SIZING SELECTION: Download the size chart (.xlsx) to accurately determine the required size REVIEWS: Review from Survival Panda Discussion of this model on the forum YOU MAY BE INTERESTED in:

The suit consists of a jacket and trousers. Jacket with a central side zipper fastener. The front has upper welt pockets with flaps and leaves, fastened with textile fasteners and side welt pockets in a “frame”, fastened with a zipper. The front and back of the jacket are lined. Turn-down collar with stand-up collar. The statutory staff suit is made of rip-stop fabric with Velcro. Back with yoke. The sleeves are set-in, single-seam, with reinforcing linings in the elbow area, with stitched cuffs fastened with a textile fastener - a slit with a puff. To attach removable shoulder straps, belt loops are located in the area of the shoulder seams; two continuous loops are sewn perpendicular to the shoulder seam. At the bottom of the jacket there is a detachable belt, the volume of which is adjustable at the side sections with an elastic band. The trousers are straight, with stitched creases and side pockets on the front halves. The front of the trousers has a zip fastening. There are darts on the back halves. On the right back half there is a welt pocket with a flap and a leaf, fastened with a textile fastener. The belt is stitched, fastened with a loop and button. To adjust the volume, the belt is tightened with an elastic band in the area of the side seams. Example of a material drawing: Additionally, you can purchase:

Combined arms suit of a new type. The new general-arms suit is made taking into account the latest requirements for uniforms and can be used virtually all year round. Structurally, the suit consists of a light jacket (tunic) and loose-fitting trousers. It is made from a durable 70/30 polyester/cotton blend with a weight of 220 g. per 1m2 of the statutory coloring “digital flora”. The jacket is equipped with a zipper, which, in turn, is covered with a windproof flap, securely fixed with textile fasteners, has a stand-up collar that prevents the fighter's neck from rubbing against the body armor, and five pockets. Two front ones, two patches on the sleeves and one internal, waterproof, for documents. The sleeves of the jacket are reinforced with a double layer of fabric and are securely fixed at the wrist with Velcro fasteners. The cut of the jacket itself is designed so that insulating layers can be slipped under it and worn either tucked into trousers or untucked. For quick identification in an emergency, and the insignia required by the regulations, the jacket has six reliable attachment points - three above the chest pockets, and three on the sleeves. The suit's trousers are loose enough so as not to restrict the fighter's movements, the knees and other loaded parts are reinforced with a second layer of fabric, and elastic bands are sewn into the belt for automatic volume control. This allows you to wear the insulating layer quite comfortably and, in critical cases, do without a waist belt. To accommodate the minimum required by a fighter, the trousers have six pockets. Two cargo labels on the sides, two slotted ones, and two rear ones. At the bottom of the legs there are drawstrings that allow you to securely fix the trousers over combat boots, as well as belt loops, they allow for more precise height adjustment and make wearing trousers tucked into shoes more comfortable. color pixel Main features: color green pixel durable material collar stand Velcro for stripes internal pocket CHARACTERISTICS CHARACTERISTICS OF THE SUIT Material: rip-stop Composition: 70/30 Density: 220 gr. Cuffs: Velcro Sealing elastic bands: ties Jacket/pants pockets: yes/yes Seasonality: demi-season

Paracord bracelets, also called survival bracelets, are made from strong parachute cord. Paracord consists of numerous intertwined strands of nylon with a core. If you divide it into two parts, you can see that under the outer shell of intertwined threads, inside there is a light cable woven from several single cords, each of which consists of many interwoven fibers.

Bracelet with rivet

Why is a bracelet woven from paracord thread called a “survival bracelet”? The thing is that, if you get into an extreme situation, it easily unravels, turning into a strong rope, indispensable for many purposes. In addition, a paracord survival bracelet can be woven into a variety of necessary outdoor gear that can help out at the most necessary moment. Therefore, a paracord bracelet is an indispensable assistant for all tourists and extreme sports enthusiasts, which in everyday life looks like an original decoration.

The bracelet can be unwoven in a few seconds to be used for its intended purpose. There are many purposes for use:

Medical care: rope and its fibers can be used as a hemostatic tourniquet, a splint for applying to a broken limb, dental floss, and can also be used to stitch wounds and make stretchers.
Foraging for food. Paracord fibers are used as fishing line, bow string, making traps, hanging food or bait.
Repair of clothes, tools. Used to sew up clothes, bandage shoes, tie up pants, and replace shoelaces. It is an indispensable thing when repairing equipment, bandaging parts of any structures, making handles for bags and other devices for transporting objects and things.
Survival. It is used in the manufacture of weapons: rewinding handles, fixing the tip to an arrow or spear, and also as a bowstring in the manufacture of a crossbow for hunting. An indispensable thing when creating and securing parts of a shelter, tying the logs of a raft, making snowshoes, making fire. To start a fire, you can use flammable individual paracord fibers or use it as a bow string when starting fire by friction.
Other purposes that can be achieved in everyday life: use as a cable for a car, a collar for animals, handcuffs, securing a load to a car, a sled, as well as paracord for drying clothes and as a rope ladder.

It should be taken into account that paracord is not used for dynamic loads, i.e. not suitable for any actions with the weight of a person (descent and ascent of a mountain, mountaineering, etc.).

DIY paracord survival bracelets

Bracelet made of quality material

To make a paracord bracelet with your own hands, you will need from 2 to 5 or more meters of this thread, depending on the width of your wrist. As a rule, there are 1-2 meters of thread per 10 cm bracelet. In addition, you will need: a fastener, a lighter to burn the ends of the thread from unraveling, tweezers and scissors. In addition to a bracelet, paracord can be used to weave a watch strap, keychain, belt, and other accessories.

Survival Bracelet: Weave

There are many patterns on how to weave a bracelet. Each of them has its own pros and cons, but the main requirement is one – the rope should easily unravel in a few seconds. With any weaving pattern, the survival bracelet should fit comfortably on the hand and have a flat shape.

How to make your own survival bracelet? You need to follow the instructions:

The ends of the rope must be burned with fire to prevent unraveling.
Four loops are made in the slot of the fastener.
You need to make a loop from the long piece of paracord by pulling it through the first four.
It extends about 5 cm, and tightens from right to left.
Four loops need to be slightly loosened, then, using tweezers, pull out three more loops between each of them, leaving the fourth on the side.
The loops need to be turned so that their left parts are in front.
The cord is threaded through four loops, as in step 3.
To complete the first row, you need to tighten the loops from right to left. Do not tighten them too tightly or twist them, this can ruin the appearance.
Steps 3,4,5 should be repeated until the required bracelet length is reached.
Once the desired length is reached, you need to pull the running cord through the last row. Its end should be on the right. You need to make gaps between the loops, and three more loops around the back of the fastener.
You need to finish the weaving by pulling the end of the rope through the loop, then cauterize it or tie it in a knot. The last option is more convenient when untying.

To unravel the bracelet, you need to untie the knot, remove the clasps and pull the end of the paracord out of the outer four loops. If you pull the end, the bracelet will come loose.

Paracord diagram for a cobra bracelet

To weave a bracelet not only for the sake of a lace, you can expand its functionality and weave into it, for example, fishing accessories: fishing line, several hooks, sinkers. Weaving stages:

The paracord is folded in half and attached to a clasp.
From one end of the cord you need to remove 3-5 cm of internal fibers.
The freed space inside the cord is filled with weights, 2-3 pieces are enough.
The cut ends are joined together with glue, the protruding threads are singed with a lighter.

Another option is possible: tape the sinkers with tape or tape to the cord so as not to violate its integrity. But the appearance of the bracelet will suffer.

Fishhooks are simply glued to electrical tape, then wrapped around the bracelet.

The required length of paracord is measured and secured with a clasp.
The fishing line is wound around the paracord of the required length. You can also push it inside the cord if it is not too thick. Usually 6 meters of fishing line is enough.
Next, around these two threads the main weaving begins, numerous visual examples of which can be found on the Internet.

Paracord is a fairly thin but very strong nylon rope. The most common use of this material is parachute lines. The very idea of paracord bracelets originated with American paratroopers. Thus, the slings did not take up space in the backpack and were always at hand in the literal sense of the word. A special weaving technique made it possible to unravel the bracelet almost instantly, turning it into a reliable and durable cable.

Paracord can be used to weave not only bracelets, but also belts, as well as many decorative items for your wardrobe.

In addition, paracord can be used as material for repairing clothing or shoes in extreme conditions. The core is easily removed from the shell, resulting in the formation of many thin threads. Paracord can be used for a wide variety of purposes - dressing wounds, making mechanisms for mountaineering or rock climbing, traps, setting up tents, traps and other self-defense items. Paracord is used to braid the handles of knives and axes, thereby making the grip more convenient, or used for decorative finishing.

Paracord bracelets in peaceful life

Paracord bracelets are mainly worn in peaceful life by supporters of extreme recreation and fans of military style. In the first case, the decoration is used as an additional measure of protection, and in the second, it is used exclusively to complement the appearance, corresponding to a military theme.

The range of paracord bracelets comes in a wide variety of options. There are not only multi-colored products, but also very bright decorations, for example, in acid shades.

It is important to remember that modern paracord bracelets available for sale are not always high-quality material that can be used for heavy loads or in survival conditions. Most paracord on the market is analog material that only superficially resembles the original. In terms of quality, it is significantly inferior to real paracord, and using threads as a cable is not only not recommended, but also prohibited. It makes sense to use such bracelets only as a stylish accessory that emphasizes individuality and a certain style direction.

It is also worth noting that American military personnel also wear paracord bracelets as talismans, as well as souvenirs reminiscent of fallen colleagues. The clasps on such unique decorations were often made from breast medallions or emblems from military uniforms.

Who would have thought that extraordinarily beautiful and practical things could be woven from a thin nylon cord? For those who want to try the paracord weaving technique, weaving patterns will be very useful. Their detailed description can be seen in this article.

About the material

Paracord is a thin nylon cord that can withstand a load of up to 250 kg. This stability is provided by the structure of the cable. It consists of a fibrous core wrapped in a smooth braid. But sometimes, under the guise of paracord, they can sell you a regular polyester cord. To prevent this from happening, you need to know that A good parkord has the following properties:

It is soft;
It burns, emitting a characteristic plastic smell and emitting a large amount of black smoke;
The braid burns much faster than the core of the cord;
Meets quality standards.

If you want to make a quality product, then use real paracord to create it.

To bring the weaving process to perfection, the craftsmen came up with a special machine. It greatly facilitates the process due to the fact that the product is tightly attached to the body of the machine. It also has a built-in ruler that will allow you to weave a bracelet to exactly the specified size without removing it from the loom. You can buy such an invention in craft stores. Or you can do it yourself. You will spend a minimum of materials, and the weaving process will become much easier. We bring to your attention a video with a master class on making a homemade machine for weaving paracord products.

Army bracelets

Typically, paracord is used for cables that hold parachute lines. However, US Army soldiers found other uses for it. No military operation is complete without a simple rope. She can save a person’s life and get him out of any trouble. To travel light, the soldiers came up with a little trick, creating a real survival kit out of parachute cord. To do this, they began to weave bracelets, inside of which they placed the necessary little things - knife blades, army badges, and the carabiner used for the clasp could also be used in case of emergency. Well, a little symbolism was introduced into this matter: each soldier wove such a bracelet with his own hands for a comrade and gave it with wishes to return from a combat operation. Before departure from the base, the bracelets were put on, and upon returning home they were removed. They were called survival bracelets.

We invite you to make such a bracelet with your own hands. It is woven with a snake pattern. To make a classic survival bracelet, take:

A piece of paracord 2 meters long;
Scissors;
Fastening.

Note. A plastic clip is perfect for fastening the product.

Pass the rope through it and insert the ends into the loop, tighten.

Place the second part of the clasp on the ropes and try it on your wrist. The bracelet should not fit your hand too tightly.

Continue weaving knots to the bottom fastener.

Pull the remaining ends through the hole in the mount, cut and melt, carefully pressing the hot tails to the clip. They must be soldered. The survival bracelet is ready.

With this simple weaving you can create an interesting bookmark.

Its upper part is made of “snake”, and the lower part is made of “cobra” weaving, which will be discussed later.

Unusual keychain

This accessory is perfect for lovers of extreme recreation. It is made with a “cobra” pattern. To complete the keychain, take:

Paracord;
Scissors;
Matches;
Carbine.

Fold the cord in half. The inner section in the form of a loop should be left the size you want to get the keychain. Weave a starting knot following the pattern.

Braid the middle section, leaving a small loop for attaching a carabiner. Turn the product over and braid it with the second row, following the instructions. You can decorate your work with a small metal accessory. As a rule, they have several eyes for fastening, through which you need to pass the cord and pull the decoration to the weave.

To complete the work, the free ends of the cord are tightened and melted with a lighter.

The stylish keychain is ready!

It also has another purpose. The fact is that previously such ropes were attached to the handle of bladed weapons. This thing is called a lanyard. It helped to easily handle the weapon and not lose it in battle. In addition, the hunters made a braid on the handle of the bladed weapon itself. In case of an emergency, this weave could also be used as a survival bracelet. A rope is simply necessary in the forest; you can use it to hang things out to dry, make a shelter or hut, set a snare for small animals, and use it as a tourniquet when injured.

Stylish accessory

From parkord you can weave not only bracelets, but also a belt. It is perfect for making a belt. Moreover, it can be used both for insurance against dangerous situations during a hike or combat operation, and for everyday wear. The photo below shows options for an army belt and a stylish accessory for women.

Video on the topic of the article

There are many options for weaving such a product and not all of them are simple. We invite you to watch video tutorials on weaving a paracord belt.

A hiking trip or a visit to the forest is an activity, although pleasant, but it is associated with certain dangers and risks. Therefore, any sane person tries to protect himself. Moreover, today there are plenty of such funds on the market. These include multifunctional knives, bags equipped with everything necessary for a hike, and other tools. Probably, many have heard about the existence of a survival bracelet, but not everyone understands well what it is, what it is for, and how to weave it with your own hands. Therefore, it is worth taking a little time to understand these issues.

Application

A paracord survival bracelet is a multifunctional item that allows you to solve several problems at once:

build a shelter;
dry things;
repair equipment;
help in playing with a child or kitten;
if you have a paperclip or a piece of branch on hand, you can make a fishing rod;
make a tourniquet to stop bleeding;
collect the onion with a branch at hand;
make a handle for a knife;
and much more.

Let's cover the topic using video.

To summarize, paracord survival bracelet is used in military and civilian applications. When unwoven, the rope can reach a length of up to five meters. Therefore, this solution is becoming increasingly popular among hiking enthusiasts.

Additionally, you can weave useful items into your survival bracelet. Thus, having such an element, you can turn from an ordinary citizen into a savvy person, ready for various incidents.

But that's not all. Serially produced products are equipped with buckle fasteners. You can mount, for example, a knife in them, which only increases the desire to have such a device. You can also weave a name tag, which may be important for the military or those who are members of various sports clubs.

It’s not for nothing that a rope is a constant companion for those involved in extreme sports and tourism. However, carrying it with you in a skein is not always possible. In the form of a bauble, it’s a different matter. As long as the rope is not needed, it simply acts as an elegant decoration on the arm. As soon as her capabilities are required, the rope unravels. Thanks to the weaving pattern, you can assemble it into a survival bracelet in ten minutes.

Step-by-step instruction

There are many weaving patterns. Each has its pros and cons, but a great solution is the ability to release the rope in one motion, so that the bracelet turns into a survival assistant.

To do it yourself you will need:

paracord (we expect that for every 10 cm of bracelet you will need up to 2 m of paracord);
clasp;
lighter;
scissors;
tweezers.

We burn the ends of the material so that they do not unravel. We take the fastener and make four free loops in its slot. We use a long piece of paracord.
Take the cord and create a loop. It needs to be pulled through the four loops made. The loop needs to be pulled out to five centimeters. Then we tighten the loops from right to left.
We loosen the four loops a little. Using tweezers, you can pull out three more loops between each pair of loops. Leave the fourth loop on the side. The hinges must be turned so that their left parts are in front. Next, the running cord must be threaded through four loops in the same way as in step 2.
We finish the first row by tightening the loops from right to left. In order for the bracelet to turn out normal, you should ensure that the loops are even, so that they are not twisted. Don't tighten it too much.
Then we repeat points 2, 3 and 4.
When the required length is reached, all that remains is to pull the running cord through the last row, the end should be on the right. We make spaces between the loops. We take the reverse part of the fastener so that it matches the first part, otherwise there will be problems with the connection.

Make three more loops around the clasp.

You can finish your survival bracelet using one of the following methods:

you can thread the end into one of the loops and then burn it using a lighter;
You can do the same, but don’t cauterize it, but tie it in a knot.

The good thing about the second option is that you don’t need additional tools (for example, scissors) to release the end.

How to unweave

To undo the bracelet, you need to untie the knot, remove the loops on the clasp, and pull the end of the cord out of the four outer loops, as shown in the photo. Pull the end to unravel. All procedures will take about twenty seconds, which is a very good indicator.

Of course, from the point of view of survival, this indicator cannot be called impressive and satisfactory, but for the majority this period of time can be called very short. Therefore, for standard conditions, say, a hike, this is enough.